Effect of strontium substitution on the structure and dielectric properties of unfilled tungsten bronze Ba4-xSrxSmFe0.5Nb9.5O30 ceramics

The effects of Sr²⁺ substitution for Ba²⁺ on phase structure, microstructure, dielectric and electric properties for Ba_4-xSr_xSmFe_0.5Nb_9.5O₃₀ (x = 0, 1, 2, 3 and 4) ceramics were systematically researched. X-ray diffraction patterns show that Ba_4-xSr_xSmFe_0.5Nb_9.5O₃₀ (x = 0, 1, 2 and 3) ceramics are tetragonal tungsten bronze compound with a space group of P4bm, while the sample for x = 4 is an orthorhombic structure compound. The result can be corroborated by the analysis of Raman spectroscopy. As the Sr²⁺ contents increase from 0 to 3, the full width at half maximum of Raman lines of all samples increase gradually, indicating that the degree of lattice distortion increase. All tetragonal tungsten bronze ceramics exhibited a broad permittivity peaks, accompanied by frequency dispersion, indicating all samples are relaxor. The electrical properties of BSSFN ceramics were further studied by complex impedance spectroscopy. XPS spectrum shows that Fe²⁺ and Fe³⁺ coexist in Ba_4-xSr_xSmFe_0.5Nb_9.5O₃₀ ceramics, and their proportion varies with the concentration of Sr²⁺.     

Fabrication,structural and vibrational properties,and physical and optical properties tailoring of nanocrystalline MoS2 films

The modification and tuning features of nanostructured films are of great interest because of controllable and distinctive inherent properties in these materials. Here, nanocrystalline MoS₂ films were fabricated on the stainless steels by a radio frequency magnetron sputtering at ambient temperature. X-ray photoelectron spectroscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction and Raman scattering spectroscopy were used to study the chemical state, chemical composition, crystal structure and vibrational properties of the fabricated MoS₂ films. The bias voltage dependent structural evolution and its influence on the optical properties of MoS₂ nanocrystalline films were systematically investigated. Besides, the residual stresses of MoS₂ nanocrystalline films were explored by employing sin²ψ approach. X-ray diffraction demonstrates that the nanocrystalline MoS₂ films have single-phase hexagonal crystal structure. All MoS₂ films are polycrystalline in nature. The bandgap values are found to be intensively dependent on bias voltage. Our findings show that the nanocrystalline MoS₂ films with different physical properties and intense quantum confinement effect can be realized through adjusting bias voltages. This work may provide deep insight for realizing transitional metal dichalcogenide-based nanostructured film optoelectronic devices with tunable physical properties through a traditional, very cost-effective, and large-scale fabrication method.     

Enhanced thermal stability of Bi2Te3-based alloys via interface engineering with atomic layer deposition

The ease of Te sublimation from Bi₂Te₃-based alloys significantly deteriorates thermoelectric and mechanical properties via the formation of voids. We propose a novel strategy based on atomic layer deposition (ALD) to improve the thermal stability of Bi₂Te₃-based alloys via the encapsulation of grains with a ZnO layer. Only a few cycles of ZnO ALD over the Bi₂Te_2.7Se_0.3 powders resulted in significant suppression of the generation of pores in Bi₂Te_2.7Se_0.3 extrudates and increased the density even after post-annealing at 500 °C. This is attributed to the suppression of Te sublimation from the extrudates. The ALD coating also enhanced grain refinement in Bi₂Te_2.7Se_0.3 extrudates. Consequently, their mechanical properties were significantly improved by the encapsulation approach. Furthermore, the ALD approach yields a substantial improvement in the figure-of-merit after the post-annealing. Therefore, we believe the proposed approach using ALD will be useful for enhancing the mechanical properties of Bi₂Te₃-based alloys without sacrificing thermoelectric performance.     

All-printed and highly stable organic resistive switching device based on graphene quantum dots and polyvinylpyrrolidone composite

We propose all printed and highly stable organic resistive switching device (ORSD) based on graphene quantum dots (G-QDs) and polyvinylpyrrolidone (PVP) composite for non-volatile memory applications. It is fabricated by sandwiching G-QDs/PVP composite between top and bottom silver (Ag) electrodes on a flexible substrate polyethylene terephthalate (PET) at ambient conditions through a cost effective and eco-friendly electro-hydrodynamic (EHD) technique. Thickness of the active layer is measured around 97 nm. The proposed ORSD is fabricated in a 3 × 3 crossbar array. It operates switching between high resistance state (HRS) and low resistance state (LRS) with OFF/ON ratio ∼14 for more than 500 endurance cycles, and retention time for more than 30 days. The switching voltage for set/reset of the devices is ±1.8 V and the bendability down to 8 mm diameter for 1000 cycles are tested. The elemental composition and surface morphology are characterized by XPS, FE-SEM, and microscope.     

Electrophoretic deposition of graphene oxide on carbon brush as bioanode for microbial fuel cell operated with real wastewater

Microbial fuel cell (MFC) is a promising technology for simultaneous wastewater treatment and energy harvesting. The properties of the anode material play a critical role in the performance of the MFC. In this study, graphene oxide was prepared by a modified hummer's method. A thin layer of graphene oxide was incorporated on the carbon brush using an electrophoretic technique. The deoxygenated graphene oxide formed on the surface of the carbon brush (RGO-CB) was investigated as a bio-anode in MFC operated with real wastewater. The performance of the MFC using the RGO-CB was compared with that using plain carbon brush anode (PCB). Results showed that electrophoretic deposition of graphene oxide on the surface of carbon brush significantly enhanced the performance of the MFC, where the power density increased more than 10 times (from 33 mWm^?2 to 381 mWm^?2). Although the COD removal was nearly similar for the two MFCs, i.e., with PCB and RGO-CB; the columbic efficiency significantly increased in the case of RGO-CB anode. The improved performance in the case of the modified electrode was related to the role of the graphene in improving the electron transfer from the microorganism to the anode surface, as confirmed from the electrochemical impedance spectroscopy measurements.     

Third order optical nonlinearities characteristics of Disperse Red1 organic dye molecules inside of polymeric nanocapsules

Measuring nonlinear optical response of a specific material in a mixture, not only leads to investigate the behavior of a particular component in various circumstances, but also can be a way to select suitable combination and optimum concentration of additives and therefore obtaining the maximum nonlinear optical signals. In this work, by using dual-arm Z-scan technique, the nonlinear refractive index of Disperse Red1 (DR1) organic dye molecules inside the core of prepared polymeric nanocapsules was measured among various materials which prepared nanocapsules were made of them. Then the measured value was compared with nonlinear refractive index of DR1 solved in dichloromethane.     

Studying the effect of organo-modified nanoclay loading on the thermal stability,flame retardant,anti-corrosive and mechanical properties of polyurethane nanocomposite for surface coating

Clay polyurethane nanocomposite (CPN) coating films were fabricated by uniformly dispersing nanoclay, organically modified with 25–30 wt.% octadecylamine in varying concentrations up to 5 wt.%, in a commercial two component, glossy, acrylic aliphatic polyurethane using ultrasonication. Organo-modified nanoclay was characterized by X-ray diffraction (XRD). The dispersion of the nanoclay into the matrix was investigated by scanning electron microscopy (SEM). CPN coating films were characterized by thermogravimetric analysis (TGA), and flame retardant, corrosion resistance and mechanical properties were also investigated. The XRD measurement indicated that, the organo-modified nanoclay particles were mainly constituted of montmorillonite with traces of quartz and calcite also found to be present. The SEM analysis showed that the nanoclay layers were dispersed and intercalated into the polyurethane coating. Thermogravimetric analysis showed that incorporating 5 wt.% organo-nanoclay into polyurethane considerably enhanced the thermal stability and increased the char residue to 14.11 wt.% relative to 4.58 for the sample without organo-nanoclay (blank polyurethane). The limiting oxygen index (LOI) test revealed that incorporation of organo-nanoclay led to a further increase in LOI values, which indicate an improvement in flame retardancy properties. The corrosion resistance also improved and this improvement increases with increase nanoclay wt.%. The mechanical resistance measurements demonstrated that the gloss of the CPN coating films slightly decreased, although hardness, adhesion and impact resistance of the CPN coating films improved with the incorporation of the organo-nanoclay.     

连续小波变换在多元函数空问中的应用

使用连续小波变换讨论了某些偏微分方程和相应的积分方程之间的关系．使用连续小波变换能够将这些偏微分方程变换成相应的积分方程，这些偏微分方程与相应的积分方程不仅在弱收敛意义下是等价的，而且在范数收敛意义下也是等价的．     

Evidence of High Vertical Wave-Number Behavior in a Continuously Stratified Reservoir: Boadella, Spain

High vertical wave-number modes clearly dominate the internal wave field during the stratification period in Boadella reservoir in northeast Spain. In this period, the extraction of hypolimnetic water, due to summer irrigation, brought the surface level down by 6 m in one month and the epilimnetic water progressively occupied the whole water column. The temperature profile, with the exception of a few meters at the surface layer, presented an almost constant temperature gradient of about 0.7°C/m. The period of the main vertical mode is 24 h with an amplitude of around 1 m. Thermistor chain records and meteorological data allow us to deduce that this mode is, at least, a third vertical mode forced by the wind, which normally has a typical periodicity of 24 h. However, when the wind changes direction from south to north, the circulation cells developed due to this forced nonstationary oscillation are destroyed. When this occurs, the Bulk Richardson number is Rib ～ 1. Similar vertical structures as a response to wind forcing should be expected in similar systems, although this has not been reported in the literature.